Technical Data Sheet
USES, FEATURES & BENEFITS ACT 1950 Series Chattahoochee Stone Sealer is deep penetrating a solvent based, non-yellowing clear coating for glazing and sealing stone. It is formulated with an Oil Modified Urethane Resin for added toughness and abrasion resistance. It delivers a warm hue which helps restore the original look of Chattahoochee stone surfaces. Ideal for sealing and glaze coating of both morter and epoxy set stone. The sealer is resistant to pool chemicals, ultra violet light and most household detergents. Packaged to be used ‘as is’ with no thinning needed. ACT Chattahoochee Stone Sealer & Glaze Coat helps prolong the life of Chattahoochee stone decks and walkways. DIRECTIONS FOR USE AND SURFACE PREPARATION Proper preparation will insure maximum adhesion, durability, and uniform coloration, ASTM D4258-83 Specification. The surface must be clean and free of all wax, grease, oil, dirt, acid, mildew, release agents and all other surface contaminants. Failure to remove grease, oil, soap or other contamination will interfere with adhesion of ACT 150. Rinse thoroughly with a power washer. Unpainted concrete surfaces should be mechanically abraded or acid etched before sealing ASTM D4260 Specification. Use ACT 14501 Clean & Etch. Power wash etched area thoroughly and NEUTRALIZE WITH A SOLUTION OF 1 PART HOUSEHOLD AMMONIA AND 20 PARTS CLEAN WATER. Rinse area thoroughly and allow to dry COMPLETELY before sealing. A properly etched surface will have the feel of 120 grit sandpaper. Extremely hard, glossy or alkaline concrete may require repeated etching. To insure maxium adhesion to aged concrte we recommend ACT 19605 Solvent Based Concrete Bonding Primer. Concrete should be at least 30 days old to reduce the possibility of the occurrence of efflorescence. Do not apply to concrete where hydrostatic pressure is present or over 3 lbs. of moisture per 1000 sq. ft. STM F1869-04. Check for a high pH, ASTM D4262 specification. Do not apply to epoxy or polyurethane coatings. Do not thin.
Technical Date Sheet SOLVENT BASED CHATTAHOOCHEE STONE SEALER
ACT1950
APPLICATION Mix product thoroughly before application. Apply in one thin coat by brush, roller or spray. Avoid heavy application resulting in runs, ponding, flood coating or puddling. Allow 1-2 hours drying time between coats. If relative humidity is high ( > 80 % ), allow an extra period of drying time between coats. One thin coat is recommended depending on the surface being coated to achieve color uniformity. Some surfaces such as inclined driveways, garages, patios, steps etc. may require a slip resistant additive for safety. Add ACT 9105 Series Talon Grip Slip Resistant Additive to the final coat. This product should not be used in place of a non-skid finish. If a non-skid finish is required, use ACT 25545 Slip-Resistant Fine. Coverage is approximately 200 sq. ft. per coat over coarse concrete and 300 sq. ft. per gallon, per coat, over smooth concrete. Do not dilute. Do not apply if the threat of rain is imminent or if the air/ surface temperature is expected to be below 40°F within the first 24 hours of appliction. Full cure is 21 days. LEAN-UP Clean immediately with Mineral Spirits PROPERTIES RESIN: Oil Modified Urethane COLOR: Amber Tint Clear SOLIDS BY WEIGHT: 31.0% VISCOSITY: 58KU @ 75F WEIGHT PER GALLON: 7.02 lbs. FLASH POINT: 105F RECOMMENDED COVERAGE: 100 sq. ft. per gallon, per coat, depending on the size of stone and porosity. DRYING TIME: @70F&50%RH To touch: 2 hours To recoat: within 8 hours or after 24 hours after application of first coat. Foot traffic: 8 hours Drying times are influenced by ambient temperature and relative humidity. VOC 580.0 grams/liter
WARNING! If you scrape, sand, or remove old paint, you PACKAGING may release lead dust. LEAD IS TOXIC. EXPOSURE TO 5 Gallon Pails LEAD DUST CAN CAUSE SERIOUS ILLNESS, SUCH AS 50 Gallon Drums BRAIN DAMAGE. ESPECIALLY IN CHILDREN. PREGNANT Part # Color Shipping UPC Per Pallet WOMEN SHOULD ALSO AVOID EXPOSURE. Wear an lbs NIOSH-approved respirator to control lead exposure. ACT19505 Amber Tint Clear 38 760428019557 36 Clean up carefully with a HEPA vacuum and a wet mop. Before you start, find out how to protect yourself For additional safety information, refer to the Safety and your family by contacting the National Lead InforData Sheet for this product. mation Hotline at 1-800-424-LEAD or log on to www. epa.gov/lead. DANGER! FLAMMABLE LIQUID AND VAPOR HARMFUL OR FATAL IF SWALLOWED. ASPIRATION HAZARD. EXTERIOR USE ONLY. CAN ENTER LUNGS AND CAUSE DAMAGE. HARMFUL IF INHALED. MAY CAUSE CENTRAL NERVOUS SYSTEM EFFECTS, INCLUDING DIZZINESS, HEADACHE OR NAUSEA. CAUSES EYE, SKIN AND RESPIRATORY TRACT IRRITATIONS. OVEREXPOSURE MAY CAUSE BLOOD, LIVER, KIDNEY DAMAGE. USE ONLY WITH ADEQUATE VENTILATION. KEEP OUT OF REACH OF CHILDREN. NOTICE: this product contains solvents. Reports have associated repeated and prolonged occupational overexposure to solvents with permanent brain and nervous system damage. Intentional misuse by deliberately concentrating and inhaling the contends may be harmful or fatal. This product contains a chemical known to the state of California to cause cancer and birth defects, or other reproductive harm. For emergency information call (800) 545-2643. For additional safety information, refer to the Safety Data Sheet for this product. Keep away from heat, sparks and flame. Do not smoke. Vapors may ignite. Extinguish all flames, burners, stoves, heaters and pilot lights and disconnect all electrical motors and appliances before use and until all vapors are gone. Prevent build-up of vapors by cross-ventilation. Do not breathe vapors or spray mist. Ensure fresh air entry during application and drying. If properly used, a respirator may offer additional protection. Obtain professional advice before using. Close container after each use. FIRST AID: In case of skin contact, wash thoroughly VOC 592.6 grams/liter - EPA Compliant with soap and water. If any product remains, gently FOR PROFESSIONAL USE ONLY rub petroleum jelly, vegetable or mineral/baby oil onto skin, then wash again with soap and water. Repeated MANUFACUTED BY: applications may be needed. Remove contaminated Anvil Coatings clothing. For eye contact, flush immediately with large 1255 Starkey Road amounts of water, for at least 15 minutes. Obtain emerLargo, Fl 33771 gency medical treatment. If swaled. 727-535-1411 DO NOT TAKE INTERNALLY. CLOSE CONTAINER AFAnvilACT.com TER EACH USE. USE WITH ADEQUATE VENTILATION. Revised 01/2016 superceds all prior publications - GRO USE PROTECTIVE CLOTHING TO AVOID CONTACT WITH SKIN AND EYES. KEEP AWAY FROM CHILDREN.
