TECHNICAL SESSIONS AT-A-GLANCE MONDAY, OCTOBER 19 Plenary Session (For complete titles and authors please see abstracts) Broadening our Horizons during the International Year of Light: Charles Townes Retrospective and Biomedical Applications
General Welcome – Peter Baker, LIA Executive Director Robert Thomas, LIA President Recognition of ICALEO® Sponsors – Robert Thomas, LIA President
Opening Words and Introduction of ICALEO Conference Chairs Silke Pflueger, ICALEO Congress General Chair
“Welding” Nerve Cells Together with Laser Tweezers (INV) (OP101) Ellen Townes-Anderson
10:40 AM
10:10 AM – 10:40 AM MORNING BREAK
11:20 AM
TECHNICAL SESSIONS AT-A-GLANCE
9:30 AM
9:20 AM
9:00 AM
Chair: Silke Pflueger Room: Grand Ballroom AB
Towards Clinical Femtosecond Laser Microsurgery Guided with Multiphoton Microscopy (INV) (OP102) Adela Ben-Yakar
Translating Light based Technologies to Patient Care (INV) (OP103) Anita Mahadevan-Jansen
12:00 PM – 1:30 PM LUNCH BREAK
38 | ICALEO® 2015 Technical Digest
Text
Peer Reviewed Paper
TECHNICAL SESSIONS AT-A-GLANCE MONDAY, OCTOBER 19 Afternoon Sessions (For complete titles and authors please see abstracts) LMP 1: New Horizons in Laser Materials Processing (Sub Plenary)
LMF 1: Advanced and Novel Precision Processing Techniques (Sub Plenary: Joint Session with Nano) Co-Chairs: Yongfeng Lu & Michelle Stock Room: Grand Ballroom E
Laser Surface Structuring with 100W of Average Power and Sub-ps Pulses (M102) Beat Neuenschwander
Laser Cutting of Composites – Two Approaches Towards an Industrial Establishment (103) Oliver Suttmann
Simultaneous Spatial Temporal Focusing: A New Paradigm for Micromachining with Femtosecond Lasers (M103) Jeff Squier
2:30 PM
Alloying Effect of Titanium on WCp/Al Compound Fabricated by Coincident Wire-powder Laser Deposition (102) Fuquan Li
2:00 PM
Laser Induced Forward Transfer (LIFT) for Direct-Write Fabrication and Assembly of Microelectronics (M101) Scott Mathews
1:30 PM
Time-resolved X-Ray Analysis of the Keyhole Behavior during Laser Welding of Steel and Aluminum at Reduced Ambient Pressure (101) Thomas Engelhardt
3:00 PM – 3:30 PM AFTERNOON BREAK LMF 2: Laser Ablation for Photovoltaics and Microelectronics I
LMF 3: Microprocessing of CFRP
Nano 1: 3D Fabrication using Femtosecond Lasers
Chair: Stefan Kaierle Room: Grand Ballroom A
Chair: Sergey Tesker Room: Grand Ballroom B
Chair: Corey Dunsky Room: Grand Ballroom D
Chair: Sami Hendow Room: Grand Ballroom E
Chair: Yongfeng Lu Room: Piedmont
The Research Status and Development of Laser Shock Peening (201) Wenwu Zhang
Research Progress of Supersonic Laser Deposition Technology: the State of the Art and Future Perspectives (INV) (301) Jianhua Yao
Study of Mechanisms of High-aspect-ratio Groove Formation in Silicon Utilizing Ultrafast Laser Radiation (INV) (M201) Ilya Mingareev
Evaluating Performance of CFRP Laser Cutting with Ultra-Short Pulses (INV) (M301) Masayuki Fujita
Nanoaquarium: Manipulation of Biocells and Worms in Electrofluidics Fabricated by Hybrid Femtosecond Laser Processing (INV) (N101) Koji Sugioka
Microstructural Effects Induced by Laser Shock Peening For Mitigation of Stress Corrosion Cracking (202) Grant Brandal
Supersonic Laser Deposition of Metal Matrix Composite Coatings (305) Bo Li
Modifications of Surface Properties of Beta Ti by Laser Surface Treatment (203) Chi-Ho Ng
Evaluation of the LDNA Surfacing Process for Cladding (303) Alexander Barroi
Mechanisms and Enhancement of Silicon Ablation Under High Fluence of a Femtosecond Laser (M202) Yung Shin
Carbon Fiber Reinforced Polymer Machining: Demonstrating Speed and Quality Using a High Power UV Laser (M303) Jim Bovatsek
Precision Fabrication of Laser Targets: Development of 2-photon Polymerization as a Nextgeneration Tool (INV) (N102) John Campbell
Softening of Hot Formed Steel (204) Thomas Harrer
The Influence of Electricmagnetic Composite Field on the WC Particles Distribution in Laser Melt Injection (304) Liang Wang
Phenomenological Model for Prediction of Complex Ablation Geometries in Metal Films using Ultrashort Laser Pulses (M203) Oliver Suttmann
High Ablation Rate Laser Processing of CFRP for Repair Purpose (M304) Ehsan Zahedi
3:50 PM
LMP 3: Cladding I
3:30 PM
LMP 2: Surface Modification
4:10 PM 4:30 PM
5:00 PM PRESIDENT’S RECEPTION – CAPITOL NORTH
Text
Peer Reviewed Paper
ICALEO® 2015 Technical Digest | 39
TECHNICAL SESSIONS AT-A-GLANCE
Chair: Christoph Leyens Room: Grand Ballroom A
TECHNICAL SESSIONS AT-A-GLANCE
LMP 4: Welding I
LMP 5: Cladding II
LMF 4: Transparent Materials Processing: Glass and Sapphire
Nano 2: Laser Processing of Low-dimensional Materials
Chair: Masoud Harooni Room: Grand Ballroom A
Chair: Anja Techel Room: Grand Ballroom B
Chair: Roland Mayerhofer Room: Grand Ballroom D
Co-Chairs: Peter Herman & Koji Sugioka Room: Piedmont
Impacts on Keyhole Oscillations and Process Pores During Laser Deep Penetration Welding (INV) (401) Joerg Volpp
Increasing Reliability and Extending Life Cycle of Critical Industrial Components with Laser Additive Processes Producing Wear Resistant and Solid Lubricating Nano-composite Coatings (501) Serge Tesker
The Magic of Nonlinear Laser Processing: Shaping Multifunctional Lab-in-fibre (INV) (M408) Peter Herman
Photonic Nanomanufacturing of High Performance Energy Devices on Flexible Substrates (INV) (201) Anming Hu
Controlled Growth of Mono- and Few-Layer Two-Dimensional Metal Chalcogenides from LaserSynthesized Nanoparticles (INV) (N202) Masoud Mahjouri-Samani
Hot Wire Laser Cladding for Repairing Martensite Precipitation Hardening Stainless Steel (502) Peng Wen
9:10 AM
Influence of Laser Parameters on Hardness of the Ni-Cr-B-Si Cladding Layer (503) Daichi Tanigawa
Process Strategy for Drilling of Chemically Strengthened Glass with Picosecond Laser Radiation (M402) Kristin Plat
9:30 AM
Vision-based Keyhole Detection in Laser Full Penetration Welding Process (403) Hongbo Zhao
(504) Sisa Pityana Cancelled
Optimizing the Processing of Sapphire with Ultrashort Laser Pulses (M403) Geoffrey Lott
3D Heat and Fluid Flow Modeling of Keyhole Laser Welding and Experimental Validation (404) Mickael Courtois
(505) Sisa Pityana Cancelled
New Presentation (513) Presented by Paul Denney
New Presentation (514) Presented by Christoph Leyens
Glass Cutting using Ultrashort Pulsed Bessel Beams (M404) John Lopez
In Situ Imaging and Control of Layer-by-layer Femtosecond Laser Thinning of Graphene (N203) Dawei Li
Femtosecond Laser Machining of Transparent, Brittle Materials: Ablative and Non-Ablative Femtosecond Laser Processing (M405) Victor Matylitsky
Ultrafast Laser Hybrid Fabricating of Macro-micro-nano-nanowire Multi-scale Structures for Near Perfect Infrared Antireflection (INV) (N204) Minlin Zhong
Experimental Investigation of Direct Diamond Laser Cladding in Combination with High Speed Camera based Process Monitoring (506) Christian Scheitler
11:00 AM
Electrodynamic Simulation of Laser Beam Absorption in Fully Penetrated Keyholes (405) Chun Deng
Measurement of Keyhole Geometry using a Coaxial Highspeed Camera Observation Method (406) Jaehun Kim
11:20 AM
10:40 AM
10:10 AM – 10:40 AM MORNING BREAK
Inline Monitoring of Laser Processing - New Industrial Results with the Low Coherence Interferometry Sensor Approach (407) Markus Kogel-Hollacher
Comparison of Nozzle Gas Shielding Techniques for Laser Cladding of Zirconium (511) Arshad Harooni
Design Features of High NA Objectives for Focusing Inside Transparent Materials (M407) Alexander Laskin
Polymer-based 3D Micro/ Nanofabrication via Twophoton Polymerization (N207) Lijia Jiang
Sensor Assisted (Remote) Welding Processes (409) Thomas Harrer
Laser Hot Wire Cladding of Thin and Thick Coatings on Steel Substrates for Wear and Corrosion Resistance (512) Klaus Kleine
Shape Control of Femtosecondlaser-induced Birefringent Structures by Controlling Spherical Aberration (M409) Takafumi Ohfuchi
Skin Effect Suppression in Infrared-laser Irradiated Planar Multi-walled Carbon Nanotube/ Cu Conductors (N206) Kamran Keramatnejad
11:40 AM
TECHNICAL SESSIONS AT-A-GLANCE
Analysis of the Physical Processes Occurring during Deep Penetration Laser Welding under Reduced Pressure (402) Remy Fabbro
9:50 AM
8:50 AM
8:30 AM
TUESDAY, OCTOBER 20 Morning Sessions (For complete titles and authors please see abstracts)
Strain and Stress Dynamics of Femtosecond Laser Bulk Processing of Transparent fcc Crystals (M406) Masaaki Sakakura
12:00 PM – 1:30 PM LUNCH BREAK
40 | ICALEO® 2015 Technical Digest
Text
Peer Reviewed Paper
TECHNICAL SESSIONS AT-A-GLANCE TUESDAY OCTOBER 20 Afternoon Sessions (For complete titles and authors please see abstracts)
Thermo-Mechanical Numerical Analysis of Hot Cracking during Laser Welding of 6xxx Aluminum Alloys (602) Haoyan Wei
Study on Laser-MAG Hybrid Weaving Characteristics for HighStrength Steel (702) Jiecai Feng
Process - Structure Property Relationship of Laser - Joined Thermoplastic Metal Hybrids (802) Philipp Amend
Microstructural and Mechanical Characterization of Aluminum–lithium Alloy 2060 Welded by Fiber Laser (603) Bing Han
Modern Hybrid Welding Process for Structural Steelwork Engineering - Laser Submerged Arc Hybrid Welding (703) Simon Olschok
Laser Localized Coating of Corrosion Resistant Metal Over Steel Weld Bead (803) Hongping Gu
Process, Microstructures and Mechanical Properties of Doublesided Fiber Laser Beam Welded T-joints of Aluminum-lithium Alloys 2060 and 2099 (604) Yunlong Zhang
Experimental Research of Hybrid Welding Processes in Combination of Gas Tungsten Arc with CO2- or Yb:YAG-laser Beam (704) Alexander Zabirov
Fabrication of Electrode Material by Laser Deposition Coupled with Chemical Dealloying (804) Zhengdong Deng
Influencing the Attachment of Bacteria Through Laser Surface Engineering (M503) Alice Gillett
Thermomechanical Analysis of the Formation of Hot Cracks in Remote Laser Welded Aluminium Fillet Welds (605) Hans Langrieger
Laser-Arc Hybrid Welding of Thick High Tensile Strength Steel Plates (705) Qinglong Pan
(805) Sisa Pityana Cancelled New Presentation (808) Underwater Laser Cutting Stefan Kaierle
Rapid Direct Laser Writing of Microfluidic Device on Siloxane Molds for Microreplication (M504) George Goh
Joining of Dissimilar and Bright Metals with Nanosecond NIR Pulsed Fiber Lasers (606) Daniel Capostagno
Comparison of Three Different Arc Modes When Laser-arc Hybrid Welding in Steel (706) Jan Frostevarg
Oxide-layer Formation on a Nickel Based Alloy using Laser Surface Melting: Experimental and Numerical Study of the Laser-metal Interaction (806) Lucille Gouton
Generation of Superhydrophobic Surfaces and Wettability Gradients on Metallic Substrates by Nanosecond Laser Irradiation (M505) Jonathan Shephard
Development of Spatter Suppression Technology for Copper by High Speed Laser Scanner Welding (807) Masanori Miyagi
Picosecond Laser Surface Texturing of Ni Substrate for Super-hydrophobic Property (M506) Xincai Wang
Modulating the Wettability Characteristics and Bioactivity of Polymeric Materials using Laser Surface Treatment (INV) (M501) Jonathan Lawrence
Nonlinear Absorption Measurements of Intraocular Lens Polymers by Integrating Z-scan (M502) Johannes Heberle
We have been able to recruit successful business owners to report on their experience of starting with an idea and build it up to a successful business. The session starts with a general outlook of the laser business on a global prospective and followed by the stories of several business owners with enough time to answer questions from the audience. Panelists: Rüdiger Brockmann, Daniel Hayden, Michelle Stock, Neil Ball, Gordon McIntosh, Bo Gu For further details see page 16.
3:30 PM
(801) Mehrshad Mehrpouya Cancelled
3:10 PM
Metallurgical Response of Weld Metal to Different Filler Metal and Joint Design Combinations of Laser-Arc Hybrid Welded Lean Duplex and Novel Ferritic Stainless Steels (701) Veli Kujanpää
4:00 PM – 7:30 PM VENDOR RECEPTION & TABLETOP DISPLAY – GEORGIA HALL, LEVEL 1
Text
Peer Reviewed Paper
ICALEO® 2015 Technical Digest | 41
TECHNICAL SESSIONS AT-A-GLANCE
Room: Grand Ballroom D
Co-Chairs: Bo Gu & Klaus Loeffler Room: Piedmont
2:50 PM
Acoustic In-process Monitoring of Laser Welding (601) Matthias Bastuck
New Presentation (807) Presented by Tony Hoult
Business Session: Advice from Experts on How to Successfully Start a Business Based on Lasers
2:30 PM
Chair: Joerg Volpp Room: Grand Ballroom B
Chair: Narasimhan Sreenivasen Room: Grand Ballroom E
LMF 5: Microprocessing Materials for Bio Applications: Polymers and Metal
2:10 PM
Chair: Remy Fabbro Room: Grand Ballroom A
Comparing the Amount of Laser Welding Spatters Resulting from Different Analyzing Methods (607) Andreas Heider
LMP 8: Emerging Applications
1:50 PM
LMP 7: Hybrid Welding
1:30 PM
LMP 6: Welding II
TECHNICAL SESSIONS AT-A-GLANCE
LMP 9: Welding III
LMP 10: LAM I
LMP 11: Lasers, Beams and Optics I
LMF 6: Laser Ablation for Photovoltaics and Microelectronics II
Nano 3: Femtosecond Laser Structuring
Chair: Daniel Capostagno Room: Grand Ballroom A
Chair: Barbara Previtali Room: Grand Ballroom B
Chair: Matthias Koitzsch Room: Athens
Chair: Rainer Kling Room: Augusta
Chair: Scott Mathews Room: Piedmont
Laser Welding of High Strength Steels (S960 and S700) with Medium Thickness (901) Lin Li
Laser-based Manufacturing of Components using Materials with High Cracking Susceptibility (INV) (1001) Frank Brueckner
Processing Surfaces with Kilowatt Level Nanosecond Pulsed Fiber Lasers (1105) Tony Hoult
Evaluating Femtosecond Laser Ablation of Graphene on SiO2/Si Substrate (M602) Tianqi Dong
Femtosecond Laser Plasma Disk for Structuring Inside Thin Transparent Film (INV) (N301) Peter Herman
Image of Laser from Rayleigh Scattering Directly Correlated to Beam Waist Measurements of HighPower Lasers (1102) John McCauley Measurement of Spectral Emissivity and Absorptivity of Laser Beam at High Temperatures (1103) Jiri Martan
Comparative Study of Laser Scribing of SnO2:F Thin Films using Gaussian and Top-Hat Beams (M603) Grant Brandal
New Generation of High Power Reflective Focusing Optics (HPRFO) (1104) Jacob Marchal
High Speed, Large Area Flexible Electronics Manufacture with an Integrated ps Fiber Laser and 3D Scanner System (M605) Timothy McComb
Evaluation of Laser Weldability of 1800 and 1900 MPa Boron Steels (902) Karl Fahlström
Full Penetration Laser Beam Welding of Thick Duplex Steel Plates with Electromagnetic Weld Pool Support (903) Marcel Bachmann Latest Advances in High Brightness Disk Lasers (904) Tracey Ryba
Morphology Evolution of γ′ Phase in K465 Nickel-base Superalloy during Laser Forming Repairing (1004) Qiuge Li Possible Structures and Process Characteristics using Miniaturized Laser Metal Deposition (1005) Christoph Leyens
Ultrafast Laser Ablation of Transparent Conductive Silver Nanowire Thin Film on PET Substrate (M604) Laurie Wipliez
Femtosecond Laser-induced Structural Modification, Joining, and Separation of Nanoelements (INV) (N302) Dongsik Kim
LMP 13: LAM II
LMP 14: Lasers, Beams and Optics II
LMF 7: Ultrashort Pulse Micromachining
Nano 4: Pulsed Laser Ablation
Chair: Daniel Capostagno Room: Grand Ballroom A
Chair: Frank Brueckner Room: Grand Ballroom B
Chair: Jan Hauptmann Room: Athens
Chair: Veli Kujanpää Room: Augusta
Chair: Yunshen Zhou Room: Piedmont
Laser-Multi-Pass-Welding of Aluminum and Steel with Sheet Thickness above 50 mm (1201) Jens Standfuss
Advanced Method for Manufacturing Hybrid Nickel Based Components by Combining Single Crystal (SX) Subcomponents with Polycrystalline (PX) Structures Generated by Laser Metal Deposition (INV) (1301) Jochen Kittel
Energy-Efficient Industrial Production Using High-Power Disk- and Direct Diode Lasers (INV) (1401) Matthias Koitzsch
Measurement of the Maximum Specific Removal Rate: Unexpected Influence of the Experimental Method and the Spot Size (M701) Benjamin Lauer
Periodic Nano-ripples on Metallic Glass Induced by Femtosecond Laser (INV) (N401) Haiou Yang
Narrow Gap Laser Welding for Potential Nuclear Pressure Vessel Manufacture (1203) Jiecai Feng
Repair of Industrial Tooling Components Made of H13 Tool Steel via Laser Direct Deposition (1303) Yung Shin
Novel Method for Measuring Beam Parameter Product and M-square (1403) Michael Scaggs
Influences on Incubation in ps Laser Micro-machining of Steel Alloys (M703) Tom Häfner
Study on Pulsed Picosecond Laser Wavelength on Ablation Quality and Efficiency of Cr12MoV Cold Work Mold Steel (N402) Baoye Wu
Finite Element Modelling of an AC Electromagnetic Weld Pool Support in Full Penetration Laser Beam Welding of Thick Duplex Stainless Steel Plates (1204) Marcel Bachmann
Microstructure and Hardness of Laser Forming Repaired 300M Steel (1304) Fenggang Liu
Advance Control of Laser Material Processing Provides Smart Solutions for Cutting, Welding and Drilling (1404) Mohammed Naeem
Inline Process Analysis and Control using Optical Measurement for the Ultra-short Pulse Laser Ablation of CAD Designed Microstructures (M704) Marco Smarra
Sensitivity Improvement of Ambient Mass Spectrometry using a Continuous Wave Infrared Laser (N403) Yao Lu
The Accuracy of Calculated Component Distortions Using the Weld Pool Length to Calibrate the Heat Source (1205) Alexander Belitzki
Strategies For High Deposition Rate Additive Manufacturing By Laser Metal Deposition (1305) Ruediger Brockmann
Developments in Beam Delivery for High Power Fiber Laser Processing (1406) Tony Hoult
Micro Materials Processing with Ultra Short Pulsed Lasers: Fundamentals, Applications and System Solutions (M706) Roland Mayerhofer
A Study on the Ablation Quality of LPAGS Influenced by Laser Beam Orientation (N404) Xizhao Wang
11:30 AM
11:10 AM
10:50 AM
LMP 12: Welding IV
11:50 AM
10:20 AM – 10:50 AM MORNING BREAK
12:10 PM
TECHNICAL SESSIONS AT-A-GLANCE
10:00 AM
9:40 AM
9:20 AM
9:00 AM
WEDNESDAY, OCTOBER 21 Morning Sessions (For complete titles and authors please see abstracts)
Narrow Gap Laser Welding by Multilayer Hot Wire Addition (1202) Alexander Kaplan
Single Pass Laser Cutting of High-precision Components: Femtosecond versus Picosecond Pulses (M702) Myriam Kaiser
12:30 PM – 2:45 PM LIA ANNUAL MEETING & AWARDS LUNCHEON – GRAND BALLROOM DE
42 | ICALEO® 2015 Technical Digest
Text
Peer Reviewed Paper
TECHNICAL SESSIONS AT-A-GLANCE WEDNESDAY, OCTOBER 21 Afternoon Sessions (For complete titles and authors please see abstracts) LMP 17: CFRP
LMF 8: Surface Texturing and Microprocessing of Metals
Nano 5: Spatial and Spectral Effects of Lasermaterial Interactions
Chair: Jens Standfuss Room: Grand Ballroom A
Chair: Yung Shin Room: Grand Ballroom B
Chair: Annett Klotzbach Room: Athens
Chair: Yasuhiro Okamoto Room: Augusta
Chair: Anming Hu Room: Piedmont
Laser Beam Welding of Electrical Contacts for the Application in Stationary Energy Storage Devices (1501) Patrick Schmitz
Investigations on Ultrahigh-speed Laser Material Deposition as Alternative for Hard Chrome Plating and Thermal Spraying (1601) Thomas Schopphoven
Comparison Between psand µs-Laser Radiation for Drilling Holes for Force Transmission Elements in CFRP-preforms (1701) Stefan Janssen
Enhanced Thermal Radiation by Femtosecond Laser Fabricating Grating Patterns on Metal Surfaces (INV) (M801) Song Liu
LBW of Steel-aluminum Corner Joints Generated by Selected Laser Material Melting (1502) Axel Jahn
Hardware-in-the-loop Control of Additive Manufacturing Processes using Temperature Feedback (1602) Wim Devesse
High-quality Cutting of CFRP with 150W Pulse Fiber Laser under Control Ambient Gas (1706) Fumihiro Matsuoka
Laser Color Marking with Color Monitoring (M802) Rahul Patwa
A Research on CFRP and Stainless Steel Joining with Fiber Lasers (1503) Junke Jiao
Freeform Laser Manufacturing based on a Parallel Robot Platform (1603) Rainer Beck
Influence of Moisture Content in Fiber Reinforced Polyetherimide on Laser Weld Seam Quality (1703) Verena Wippo
Investigations of Welding Instabilities and Weld Seam Formation during Laser Micro Welding of Ultra-thin Metal Sheets (M803) Michael Seiler
Laser Cleaning of Commercial Al Alloy Surface for TIG Welding (1504) Minlin Zhong
Remanufacturing of Compressor Blade by Laser Direct Deposition and Subsequent Multi-axis Milling (1605) Jie Sun
Controlled Laser Welding of Thermoplastic Interior Structures (1704) Peter Jaeschke
Pulsed Laser Ablation of SiCp/Al Composite (M804) Huanzhen Zhang
Kilowatt Average Power Short-Pulse Laser Processing of CFRP Quality Challenges (1705) Rudolf Weber
Surface Structure Formation Mechanism in WE54 Alloy Subjected to Ultrafast Laser Texturing (M805) Indira Khadka
3:20 PM Laser-assisted Nanomanufacturing and In-situ Diagnostics (INV) (N504) David Hwang
3:40 PM 4:00 PM
Influence of Resonant and Non-Resonant Vibrational Excitation of Ammonia Molecules in Gallium Nitride Synthesis (N503) Hossein Rabiee Golgir
4:20 PM
Aluminum Welding Comparison with Disk and Direct Diode Lasers (1506) Thomas Harrar
Laser Processing for Production of Lithium-ion Batteries (INV) (N501) Wilhelm Pfleging
4:40 PM – 5:15 PM AFTERNOON BREAK
Text
Peer Reviewed Paper
ICALEO® 2015 Technical Digest | 43
TECHNICAL SESSIONS AT-A-GLANCE
LMP 16: LAM III
3:00 PM
LMP 15: Welding V
TECHNICAL SESSIONS AT-A-GLANCE
9:50 AM
LMP 18: Welding VI
LMP 19: LAM IV
LMP 20: Cutting and Drilling
LMF 9: Advances in Lasers, Optics, and Beam Delivery
Nano 6: Advanced Laser Applications
Chair: Xianfeng Shen Room: Grand Ballroom A
Chair: Rainer Beck Room: Grand Ballroom B
Chair: Sarah Nothdurft Room: Grand Ballroom E
Chair: Rahul Patwa Room: Grand Ballroom D
Chair: Masoud MahjouriSamani Room: Piedmont
Modelling of Weld Pool Phenomena in TIG, CO2-laser and Hybrid (TIG+CO2-laser) Welding (1810) Alexander Zabirov Improved Process and New Laser Source for Spatter Free Welding of Electronic Copper Components (1802) David Havrilla
Spectroscopic Monitoring and Melt Pool Temperature Estimation during the Laser Metal Deposition Process (1901) Dieter De Baere Laser Powder Deposition of WC Particle Reinforced Metal Matrix Composites (1911) Hongbo Zhao
Temperature Characteristics at Cut Front Edge during Fiber Laser Cutting of AA2219 Aluminum Alloy (2010) Cong Chen Visualization of Flow Separation inside Cut Kerf during Laser Cutting of Thick Sections (2002) Chi Zhang
Effect of Large Deflection Angle on the Laser Intensity Profile Produced by AOD Scanners in High Precision Manufacturing (INV) (M901) Tiansi Wang
Multi-dimensional Pattern Fabrication on 3D Surface by Laser Ablation: Principle and Applications (INV) (N601) Xiaoyan Zeng
Laser Beam Welding of Ultrahigh Strength Martensitic Steels with Active Cooling (1803) Benjamin Gerhards
Microstructure and Mechanical Properties of Laser Solid Formed Titanium Alloys (1903) Xin Lin
System Technology for Dynamic Beam Shaping (2003) Jan Hauptmann
High Average Power, High Energy Fiber Delivery and Temporal Compression of Ultrafast Pulses (M902) Eric Mottay
Research of Ceramic Coatings Prepared by Laser Cladding in Different Assembly Way for Ultra-fine Powder (N602) Qunli Zhang
Preliminary Laser Welding Tests of 22MnB5 Steel with Butt Joint and Lap Joint Configurations (1804) Jukka Siltanen
Influence of Laser Power on the Surfacing Microstructures and Microhardness Properties of Ti-6Al-4V-Cu Composites using the NdYAG Fiber Laser (1904) Mutiu Folorunsho Erinosho Analysis of Selective Laser Melting of Resorbable Bioceramics (1905) Pascal Aubry
Waveform Tuned Pulsed Fiber Lasers for Gas Assisted Cutting of Bright Metals (2004) Daniel Capostagno
Ultra-short Pulse Laser Beam Shaping for Micro-structuring using a Deformable Mirror (M903) Marco Smarra
Higher Power Fiber-Coupled Diode Lasers Enable New Application Fields (N603) David Matthews
Into Polarization Control in Laser Cutting with Direct Diode Lasers (2005) Gonçalo Costa Rodrigues
High Power Ultrafast Lasers for the Precision Manufacturing Industry (M904) Michael Mielke
A Method of Reducing the Optical Path in Spectral Beam Combining (N604) Zhanda Zhu
LMP 20
LMF 9
LMF 10: Transparent Materials Processing: Glass Joining with Ultrashort Pulses
Effect of Optical Parameters on Fiber Laser Welding of Ultra High Strength Steels and Weld Mechanical Properties at Sub-zero Temperatures (1805) Antti Salminen
10:10 AM – 10:40 AM MORNING BREAK LMP 18
LMP 19
10:40 AM
Characterization of Direct Laser Deposited Low Modulus Ti-26Nb Alloy on Ti-6Al-4V for Biomedical Applications (1906) Marie Fischer
Wavelength Effect on Striation Formation during Metal Laser Cutting (2006) El-Hachemi Amara
Microlens Beam Homogenizer for Excimer Laser Processing (M905) Yuhua Jin
Investigation of LBW Characteristics Using Ta Thermocouple Wire for Instrumented Fuel Irradiation Test (1811) Soosung Kim
Laser Micro Melting (1907) André Streek
Use of a Diffractive Optic for High Power Laser Cutting (2007) Paul Hilton
Compact, High Power, Hybrid Femtosecond Lasers (M906) Eric Mottay
Comparison of Processing Window and Porosity Distribution in Laser Welding of 10mm 30CrMnSiA Ultra-high Strength between Flat (1G) and Horizontal (2G) Position (1808) Xianfeng Shen Effect of the Welding Process and Filler Material on the Fatigue Behaviour of 960 MPa Structural Steel at a Butt Joint Configuration (1809) Jukka Siltanen
Direct Metal Deposition of Titanium Matrix Composites using B4C Powder (1908) Pascal Aubry
Hybrid Laser Drilling of Cooling Holes by Using Millisecond Pulsed Fiber Laser Radiation and Ultrashort Pulsed Laser Radiation (2008) Hermann Uchtmann
Laser Micromachining with Short Pulsed Fiber Lasers (M907) Rouzbeh Sarrafi
Laser Soldering and Brazing of Steel-aluminum Sheets for Tailored Hybrid Tubes (1909) Sarah Nothdurft
Laser Cutting of Copper and Brass Alloys by High Brilliance Diode Source with an Extremely Low BPP (2011) Barbara Previtali
Surface Engineering 2.0 – Novel Material Properties and Surface Functions Generated by Lasers with Line Focus Geometry (M908) Jens Meinschien
11:20 AM
Hybrid Laser-MAG Welding of S460ML Steel Plates: Weldability and Consequences of Dropping on Weld Quality (1806) Fabrice Chaussé
11:00 AM
Chair: Klaus Kleine Room: Piedmont
11:40 AM
TECHNICAL SESSIONS AT-A-GLANCE
9:30 AM
9:10 AM
8:50 AM
8:30 AM
THURSDAY, OCTOBER 22 Morning Sessions (For complete titles and authors please see abstracts)
Effect of Focusing Condition on Micro-welding Characteristic of Glass by Picosecond Pulsed Laser (INV) (M1001) Yasuhiro Okamoto
Bridge The Gap: Advancing USP-based Glass Joining Towards Industrial Applications (INV) (M1002) Michael Schmidt
12:00 PM – 1:30 PM LUNCH BREAK
44 | ICALEO® 2015 Technical Digest
Text
Peer Reviewed Paper
TECHNICAL SESSIONS AT-A-GLANCE THURSDAY, OCTOBER 22 Closing Plenary (For complete titles and authors please see abstracts) New and Unusual Lasers Chair: Silke Pflueger Room: Grand Ballroom A
3:30 PM – 4:15 PM FAREWELL BREAK
ICALEO® 2015 Technical Digest | 45
TECHNICAL SESSIONS AT-A-GLANCE
3:00 PM
Development of a Pulsed Ultraviolet Laser for Planetary Exploration (INV) (C104) Dietmar Kracht
2:30 PM
VCSEL Arrays Expanding the Range of High-power Laser Systems and Applications (INV) (C103) Armand Pruijmboom
2:00 PM
Next Generation Scientific Lasers: A New Era of Capabilities and Applications (INV) (C102) Constantin Haefner
1:30 PM
High Power CO Lasers: New Application Potential (INV) (C101) Andrew Held
