Accessory
INSTALLATION INSTRUCTIONS
Application
2011 ODYSSEY (EXCEPT LX)
REMOTE CONTROL ENGINE STARTER
PARTS LIST Remote Control Engine Starter Unit Kit P/N 08E91-E22-101A
Publications No.
AII 43923-46569 Issue Date
JUNE 2011
Remote Control Engine Starter Attachment Kit P/N 08E92-TK8-100 Engine starter harness
Transmitter
Control unit
Control unit bracket
Template Antenna
2
Key ring
Relays
21 Wire ties
Protective tape 6
Urethane tapes
Fuse label Aluminum tape
Caution label 8 mm Nut
Accessory User’s Information Manual
Quick Start Guide
© 2011 American Honda Motor Co., Inc. – All Rights Reserved.
AII 43923-46569 (1106)
08E92-TK8-1000-90
1 of 22
TOOLS AND SUPPLIES REQUIRED
INSTALLATION
Phillips screwdriver
Customer Information: The information in this installation instruction is intended for use only by skilled technicians who have the proper tools, equipment, and training to correctly and safely add equipment to your vehicle. These procedures should not be attempted by “do-it-yourselfers.”
Flat-tip screwdriver Diagonal cutters Ratchet 8 mm, 10 mm, and 12 mm Sockets 10 mm Open end wrench Trim Tool Set (SOJATP2014) (Available through the Honda Tool and Equipment program. On the iN, click on: Service/Service Bay/Tool and Equipment Program, then enter the number under “Search.” Or call 888-424-6857.)
NOTE: This antenna should only be installed if the ambient air temperature 15°C (60°F) or above. 1.
Make sure you have the anti-theft code for the audio unit and navigation system (if equipped), then write down the radio station presets.
2.
Move the driver’s seat all the way back.
3.
Remove the air duct (two clips).
Isopropyl alcohol Scissors Small flat-tip screwdriver Shop towel
CLIP
Tape measure
AIR DUCT
HDS (Honda Diagnostic System) Needle nose pliers Torque wrench Masking tape Illustration of the Remote Control Engine Starter Installed on the Vehicle ANTENNA RELAY 3A FUSE CONTROL UNIT
012903AD
4.
40A FUSE
2 of 22
ENGINE STARTER HARNESS
Disconnect the negative cable from the battery.
021516AY
AII 43923-46569 (1106)
© 2011 American Honda Motor Co., Inc. – All Rights Reserved.
Setting the Control Unit 5.
7.
Touch the metal part of the screwdriver to any metal part of the vehicle to discharge any static electricity.
Using isopropyl alcohol on a shop towel, clean the area where the protective tape will attach. Attach the protective tape to the control unit over the switches.
CONTROL SMALL FLAT-TIP UNIT SCREWDRIVER
CONTROL UNIT
Discharge any static electricity.
SWITCHES SWITCHES
PROTECTIVE TAPE
SWITCHES
Clean with isopropyl alcohol.
ADHESIVE BACKING
SET
772505AS
8.
Remove the roof console. •
Using a small flat-tip screwdriver wrapped with a shop towel, pry out and remove the left and right lens (four retaining tabs each).
•
Open the sunglass holder and remove the four screws.
•
Remove the roof console (unplug the vehicle connectors).
SW:1 RR Junction unit ------------------- > ON SW:2 Trunk or Tailgate -------------------- > ON SW:3 Smart Entry --------------------------- > OFF SW:4 Horn or Buzzer Answerback ---- > OFF
VEHICLE CONNECTORS
SW:5 Trunk Main SW----------------------- > OFF SW:6 Reserve--------------------------------- > OFF
021001AY
6.
Using a small flat-tip screwdriver, change the switches on the control unit to the setting shown above.
ROOF CONSOLE
NOTE: • The switches must be selected before the control unit is plugged in.
SUNGLASS HOLDER Open.
•
If the switch setting is not correct, the remote engine starter will not operate correctly.
•
If you change the switch settings with the unit connected, you must disconnect the unit then reconnect it before the settings change.
4 SCREWS
4 RETAINING TABS
© 2011 American Honda Motor Co., Inc. – All Rights Reserved.
AII 43923-46569 (1106)
4 RETAINING TABS
LEFT LENS RIGHT LENS
012802BX
3 of 22
9.
Rotate the sunvisor holders 45° counterclockwise and remove the two sunvisor holders.
11. Pull away the door seal from around the driver’s A-pillar trim. Using a trim tool, remove the A-pillar cover (two retaining tabs and one hook).
SUNVISOR HOLDER
A-PILLAR COVER
HOOK 2 RETAINING TABS A-PILLAR COVER
Rotate. WASHER-BOLT
PASSENGER’S SUNVISOR HOLDER TRIM TOOL
DRIVER’S SUNVISOR HOLDER
10. Remove the driver’s sunvisor.
DRIVER’S A-PILLAR TRIM
021003BY
12. Remove the washer-bolt from the driver’s A-pillar.
•
Turn the sunvisor toward the driver’s seat.
•
Locate the slot in the sunvisor holder, and insert a flat-tip screwdriver into the slot. Push in and hold the retaining tab.
•
DOOR SEAL Pull away.
700215AE
13. Remove the driver’s A-pillar trim (three clips). DRIVER’S A-PILLAR TRIM
While holding the retaining tab, push up on the sunvisor and rotate toward the door to remove. NOTE: If the retaining tab did not stay pushed in, return the driver’s sunvisor to its original position and repeat the above steps.
•
Remove the driver’s sunvisor (unplug the vehicle connector).
Push and hold the retaining tab.
FLAT-TIP SCREWDRIVER
FRONT Rotate. CLIP SLOT FRONT
Push and hold.
2 CLIPS 021004CY
HOLDER Rotate towards the door. VEHICLE CONNECTOR
FRONT DRIVER’S SUNVISOR
4 of 22
021002BY
AII 43923-46569 (1106)
© 2011 American Honda Motor Co., Inc. – All Rights Reserved.
14. Lower the tilt lever and pull the steering wheel out. STEERING COLUMN UPPER COVER
17. Remove the left center console side panel (one clip, two clips, four retaining tabs and one pin). Click to Play
SELF-TAPPING SCREW
Click to Stop
4 RETAINING TABS
PIN CLIP LEFT CENTER CONSOLE SIDE PANEL
4 RETAINING TABS
2 CLIPS 012702BE
STEERING WHEEL Push.
Routing the Engine Starter Harness
021001AB
18. Using isopropyl alcohol on a shop towel, thoroughly clean the fuse block and the fuse case where the 40A fuse label and 3A fuse label will attach.
15. Remove the steering column upper cover (two self-tapping screws and four retaining tabs). NOTE: Adjust the angle of the steering wheel to access each self-tapping screw.
FUSE BLOCK
40A FUSE LABEL
RELAY BLOCK
16. Remove the steering column lower cover (three washer-screws).
ENGINE STARTER HARNESS
RELAY 3A FUSE LABEL
FUSE CASE
021005BY
19. Attach the 40A fuse label, and the 3A fuse label to the fuse block, and the fuse case on the engine starter harness. STEERING COLUMN LOWER COVER
WASHERSCREW
© 2011 American Honda Motor Co., Inc. – All Rights Reserved.
20. Plug two relays into the relay block on the engine starter harness. 021002BB
AII 43923-46569 (1106)
5 of 22
21. Route the engine starter harness under the dashboard as shown. FUSE BOX
23. Secure the engine starter harness to the vehicle harness with one wire tie. PARKING BRAKE BRACKET
PARKING BRAKE BRACKET
ENGINE STARTER HARNESS
BRAKE PEDAL
FUSE BOX 021101BY
22. Secure the clip from the engine starter harness relay block to the hole in the parking brake bracket. FUSE BOX
PARKING BRAKE BRACKET
HOLE
ENGINE STARTER HARNESS
VEHICLE HARNESS
WIRE TIE
ENGINE STARTER HARNESS BRAKE PEDAL
021103AY
24. Align the white tape on the engine starter harness with the vehicle clip, and secure the engine starter harness to the vehicle harness with one wire tie. STEERING COLUMN LOWER COVER OPENING
WHITE TAPE Align. ENGINE STARTER HARNESS
VEHICLE HARNESS
RELAY BLOCK BRAKE PEDAL
CLIP
021102AY
WIRE TIE
6 of 22
AII 43923-46569 (1106)
VEHICLE CLIP
021104BY
© 2011 American Honda Motor Co., Inc. – All Rights Reserved.
25. Route the engine starter harness up the steering column to the ignition switch. ENGINE STARTER HARNESS 12-PIN CONNECTOR
27. Unplug the vehicle 8-pin connector from the wiper switch, and plug it into the engine starter harness 8-pin connector. Plug the remaining engine starter harness 8-pin connector into the wiper switch. STEERING COLUMN UPPER COVER OPENING
ENGINE STARTER HARNESS
ENGINE STARTER HARNESS 8-PIN CONNECTOR
STEERING WHEEL
STEERING COLUMN UPPER COVER OPENING
ENGINE STARTER HARNESS 7-PIN CONNECTOR (WHITE)
051701AY
26. Unplug the vehicle 7-pin connector (white) from the ignition switch, and plug it into the engine starter harness 7-pin connector (white). Plug the remaining engine starter harness 7-pin connector (white) into the ignition switch. STEERING WHEEL
STEERING WHEEL
ENGINE STARTER HARNESS 8-PIN CONNECTOR
IGNITION SWITCH
WIPER SWITCH
VEHICLE 8-PIN CONNECTOR
021201AY
28. Unplug the cable reel 20-pin connector, and release the harness cover (two clips).
ENGINE STARTER HARNESS 7-PIN CONNECTOR (White)
CLIP
CABLE REEL 20-PIN CONNECTOR
HARNESS COVER
STEERING WHEEL STEERING COLUMN UPPER COVER OPENING STEERING COLUMN LOWER COVER OPENING
VEHICLE 7-PIN CONNECTOR (White)
© 2011 American Honda Motor Co., Inc. – All Rights Reserved.
CLIP 021202BY
021106AY
AII 43923-46569 (1106)
7 of 22
29. Route the engine starter harness through the steering column area as shown. HARNESS COVER
33. Secure the 8-pin connector and engine starter harness to the vehicle harness with one wire tie as shown.
VEHICLE HARNESS WIRE TIE
WIPER SWITCH
ENGINE STARTER HARNESS
VEHICLE HARNESS
ENGINE STARTER HARNESS 12-PIN CONNECTOR
FRONT 8-PIN CONNECTOR
STEERING COLUMN UPPER COVER OPENING
STEERING WHEEL
VEHICLE 12-PIN CONNECTOR LIGHT SWITCH
ENGINE STARTER HARNESS
STEERING COLUMN UPPER COVER OPENING
ENGINE STARTER HARNESS
021203BY
30. Unplug the vehicle 12-pin connector from the light switch, and plug it into the engine starter harness 12-pin connector. Plug the remaining engine starter harness 12-pin connector into the light switch.
ENGINE STARTER HARNESS
STEERING WHEEL
WIRE TIE
TAPE
VEHICLE HARNESS 021205BY
31. Secure the 12-pin connectors and the engine starter harness with one wire tie. STEERING COLUMN UPPER COVER OPENING WIRE TIE
12-PIN CONNECTORS ENGINE STARTER HARNESS
LIGHT SWITCH
STEERING WHEEL 021204BY
32. Reinstall the harness cover, and reconnect the cable reel 20-pin connector unplugged in step 28.
8 of 22
AII 43923-46569 (1106)
© 2011 American Honda Motor Co., Inc. – All Rights Reserved.
34. Secure the 7-pin connector and the engine starter harness to the vehicle harness with two wire ties as shown.
37. Cut one urethane tape, and wrap one urethane tape around the engine starter harness 5-pin connector as shown.
NOTE: Make sure that the connectors and harness are not pinched, or interfering with the steering wheel when moved for adjustment. IGNITION SWITCH
STEERING WHEEL
7-PIN CONNECTOR
URETHANE TAPE
VIEWED FROM URETHANE SIDE URETHANE TAPE
Do not cover this area.
Discard.
25 mm WIRE TIE ENGINE STARTER HARNESS 5-PIN CONNECTOR
20 mm
ENGINE STARTER HARNESS
ENGINE STARTER HARNESS 5-PIN CONNECTOR
Align. VEHICLE CLIP
7-PIN CONNECTOR OUTSIDE INSIDE VEHICLE HARNESS
FRONT VIEWED FROM VEHICLE BOTTOM HARNESS WIRE WIRE TIE TIE
7-PIN CONNECTOR ENGINE STARTER HARNESS
021206CY
35. Secure the engine starter harness to the vehicle harness with one wire tie. DRIVER’S KICK PANEL
ENGINE STARTER HARNESS
070801BY
FUSE BOX
PARKING BRAKE BRACKET
WIRE TIE Loosely secure.
ENGINE STARTER HARNESS
VEHICLE HARNESS
WIRE TIE 021207BY
36. Loosely secure the engine starter harness to the vehicle harness with one wire tie.
© 2011 American Honda Motor Co., Inc. – All Rights Reserved.
AII 43923-46569 (1106)
9 of 22
38. Unplug the vehicle 5-pin connector from the fuse box, and plug it into the engine starter harness 5-pin connector. Plug the remaining engine starter harness 5-pin connector into the fuse box.
39. Secure the 5-pin connectors and the engine starter harness with one wire tie. FUSE BOX
5-PIN CONNECTOR
NOTE: Check that the engine starter harness 5-pin connector is properly connected and locked securely. A loose connection may cause engine to stall. 2 Push.
2 1 Pull. Push.
WIRE TIE
3
1 UNLOCK
LOCK
2 ENGINE STARTER HARNESS 5-PIN CONNECTORS
VEHICLE 5-PIN CONNECTOR
DRIVER’S KICK PANEL
FUSE BOX FUSE BOX
ENGINE STARTER HARNESS
021209CY
40. Route the engine starter harness up, and loosely secure it to the vehicle harness with two wire ties.
WIRE TIE Loosely secure.
ENGINE STARTER HARNESS
VIEWED FROM FRONT PLUGGING POINT
DASHBOARD
ENGINE STARTER HARNESS 12-PIN CONNECTOR
VEHICLE HARNESS
021208BY
ENGINE STARTER HARNESS 4-PIN CONNECTOR
DRIVER’S KICK PANEL
10 of 22
AII 43923-46569 (1106)
ENGINE STARTER HARNESS
FUSE BOX
021210DY
© 2011 American Honda Motor Co., Inc. – All Rights Reserved.
41. Locate the 4-pin connector taped to the vehicle harness, and remove the tape to release the connector. Plug the engine starter harness 4-pin connector into the vehicle 4-pin connector. VEHICLE TAPE HARNESS Remove.
43. Route the engine starter harness across the dashboard as shown. LEFT KNEE BOLSTER
DASHBOARD
ENGINE STARTER HARNESS
VEHICLE 4-PIN CONNECTOR
ENGINE STARTER HARNESS 4-PIN CONNECTOR
OBD II DATA LINK CONNECTOR
VEHICLE HARNESS
WIRE TIE Loosely secure. 4-PIN CONNECTOR ENGINE STARTER HARNESS 12-PIN CONNECTOR
FUSE BOX
DRIVER’S KICK PANEL
021212BY
44. Align the white tape on the engine starter harness with the hole on the vehicle bracket, and secure the engine starter harness to the vehicle bracket with one wire tie.
021211CY
WHITE TAPE Align.
HOLE
VEHICLE BRACKET
WIRE TIE
WHITE TAPE
42. Loosely secure the 4-pin connectors to the vehicle harness with one wire tie. ENGINE STARTER HARNESS
VEHICLE BRACKET
© 2011 American Honda Motor Co., Inc. – All Rights Reserved.
AII 43923-46569 (1106)
OBD II DATA LINK CONNECTOR
021213BY
11 of 22
45. Secure the engine starter harness. Without Ambient Light: Secure the wire tie to the dashboard. ENGINE STARTER HARNESS
46. Using isopropyl alcohol on a shop towel, thoroughly clean the left knee bolster where the aluminum tape will attach. Attach the engine starter harness to the inside of the left knee bolster with the aluminum tape.
DASHBOARD
WIRE TIE
LEFT KNEE BOLSTER
ALUMINUM TAPE
021214BY
With Ambient Light: Secure the wire tie to the ambient light harness. ENGINE STARTER HARNESS
ALUMINUM TAPE
LEFT KNEE BOLSTER Clean with an isopropyl alcohol.
AMBIENT LIGHT HARNESS
ENGINE STARTER HARNESS
021216BY
47. Continue routing the engine starter harness as shown.
WIRE TIE
VEHICLE 12-PIN CONNECTOR
AMBIENT LIGHT
ENGINE STARTER HARNESS
SELECT LEVER
ENGINE STARTER HARNESS 12-PIN CONNECTOR
021215BY
ENGINE STARTER HARNESS
DRIVER’S DASHBOARD SIDE PANEL OPENING
021217CY
48. Unplug the vehicle 12-pin connector from the select lever, and plug it into the engine starter harness 12-pin connector. Plug the remaining engine starter harness 12-pin connector into the select lever.
12 of 22
AII 43923-46569 (1106)
© 2011 American Honda Motor Co., Inc. – All Rights Reserved.
49. Align the branch section of the engine starter harness to the branch section of the vehicle harness and secure the engine starter harness to the vehicle harness with two wire ties. VEHICLE VEHICLE CLIP HARNESS
WIRE TIE
Installing the Antenna 50. Using two pairs of needle nose pliers, bend the antenna plate according to the full scale drawing as shown.
DRIVER’S DASHBOARD SIDE PANEL OPENING
ANTENNA
ANTENNA
9 mm (0.3 in.)
ENGINE STARTER HARNESS
ANTENNA PLATE 16 mm (0.6 in.)
ENGINE STARTER HARNESS BRANCH SECTION Align.
VEHICLE HARNESS
021218CY
2 NEEDLE NOSE PLIERS
SCALE ANTENNA PLATE
© 2011 American Honda Motor Co., Inc. – All Rights Reserved.
AII 43923-46569 (1106)
021501BY
13 of 22
51. Using scissors, cut out the template.
53. Starting from the antenna end of the antenna cable, wrap four urethane tapes to the antenna cable as shown.
Cut out. ANTENNA
ANTENNA CABLE 70 mm (2.7 in.) ANTENNA CABLE 150 mm (5.8 in.) TEMPLATE SCISSORS 4 URETHANE TAPES
021502AY
52. Using strips of masking tape, attach the template to the front windshield. Align the template with the black ceramic paint as shown. BLACK CERAMIC PAINT
870 mm (34.1 in.)
ANTENNA CABLE
TEMPLATE
URETHANE TAPE Cut in half. Align. MASKING TAPES
140 mm (5.5 in.)
120 mm (4.7 in.)
URETHANE TAPE
021504BY
54. Using scissors, cut one urethane tape in half. Wrap one piece of cut urethane tape to the antenna cable as shown.
FRONT Align this end with WINDSHIELD the end of the black ceramic paint. TEMPLATE
14 of 22
021503BY
AII 43923-46569 (1106)
© 2011 American Honda Motor Co., Inc. – All Rights Reserved.
55. Using isopropyl alcohol on a shop towel, thoroughly clean the antenna plate where the urethane tape will attach. URETHANE TAPE
NOTE: Be careful not to crease the headliner for the following procedures. 57. Using isopropyl alcohol on a shop towel, thoroughly clean the front windshield where the antenna will attach. HEADLINER
FRONT WINDSHIELD Clean with isopropyl alcohol.
ANTENNA PLATE Clean with isopropyl alcohol.
URETHANE TAPE
TEMPLATE ANTENNA PLATE
ANTENNA
ANTENNA ADHESIVE BACKING Remove.
021506BY
58. Remove the adhesive backing from the antenna. Insert the antenna plate under the headliner, align the antenna with the template, and attach the antenna to the front windshield. NOTE: Make sure that the antenna is firmly attached to the front windshield.
ANTENNA
59. Remove the template.
ANTENNA PLATE
60. Gently tuck the antenna cable under the headliner as shown. Be careful not to crease the headliner. VEHICLE PANEL
URETHANE TAPE
HEADLINER HEADLINER 021505BY
56. Attach the remaining piece of cut urethane tape to the antenna plate as shown.
ANTENNA CABLE
ANTENNA CABLE
HEADLINER
ANTENNA CABLE 021507CY
© 2011 American Honda Motor Co., Inc. – All Rights Reserved.
AII 43923-46569 (1106)
15 of 22
61. Route the antenna cable alongside the vehicle harness, and secure it to the vehicle harness with four wire ties.
63. Route the antenna cable along the vehicle harness, and secure it to the vehicle harness with one wire tie.
ANTENNA CABLE
4 WIRE TIES
VEHICLE HARNESS
WIRE TIE Loosely secured in step 42.
WIRE TIE
ANTENNA CABLE VEHICLE HARNESS 4-PIN CONNECTORS
DRIVER’S A-PILLAR 021508AY
62. Route the antenna cable down and under the dashboard as shown.
FUSE BOX DRIVER’S KICK PANEL
DASHBOARD HOLE FRONT ANTENNA CABLE
021510CY
64. Route the antenna cable under the wire tie loosely secured in step 42, and tighten the wire tie. 65. Route the antenna cable along the engine starter harness, and under the three wire ties loosely secured in steps 36 and 40.
VEHICLE HARNESS
WIRE TIE Do not tighten yet.
DRIVER’S A-PILLAR
VEHICLE HARNESS
FUSE BOX
VEHICLE HARNESS ANTENNA CABLE
021509AY
ANTENNA CABLE
DRIVER’S KICK PANEL
16 of 22
AII 43923-46569 (1106)
ENGINE STARTER HARNESS
VEHICLE HARNESS
WIRE TIE Do not tighten yet. 021511CY
© 2011 American Honda Motor Co., Inc. – All Rights Reserved.
Installing the Control Unit 66. Under the dash near the fuse box, locate the parking brake bracket flange nut. Remove the parking brake bracket flange nut. CONTROL UNIT BRACKET
68. Plug the antenna cable terminal, and the engine starter harness 28-pin connector into the control unit. CONTROL UNIT
ANTENNA CABLE TERMINAL
FUSE BOX
CONTROL UNIT
PARKING BRAKE BRACKET 8 mm NUT
ENGINE STARTER HARNESS 28-PIN CONNECTOR PARKING BRAKE BRACKET FLANGE NUT Reuse. Align.
PARKING BRAKE BRACKET
PARKING BRAKE BRACKET
ANTENNA CABLE
021513AY
69. Install the control unit to the control unit bracket. CONTROL UNIT
8 mm NUT
CONTROL UNIT BRACKET
FUSE CASE
CLIP HOLE
NOTCH CONTROL UNIT BRACKET
PARKING BRAKE BRACKET
CONTROL UNIT BRACKET
VEHICLE PANEL 021512CY
CONTROL UNIT BRACKET
67. Install the control unit bracket on top of the parking brake bracket and align the notch in the control unit bracket with the edge of the parking brake bracket. Reinstall the parking brake bracket flange nut, and torque it to 18.7 to 24.5 N·m (13.6 to 17.8 lbf·ft). Install the 8 mm nut (supplied) on top of the parking brake bracket flange nut, and torque it to 18.7 to 24.5 N·m (13.6 to 17.8 lbf·ft).
FUSE CASE
PARKING BRAKE BRACKET
FUSE BOX
CONTROL UNIT
CONTROL UNIT BRACKET 021514CY
70. Attach the clip on the engine starter harness fuse case to the hole in the control unit bracket.
© 2011 American Honda Motor Co., Inc. – All Rights Reserved.
AII 43923-46569 (1106)
17 of 22
71. Bundle up the excess antenna cable, and secure it to the vehicle harness with the two wire ties loosely secured in step 40. Tighten the lower wire tie loosely secured in step 36. WIRE TIE
VEHICLE HARNESS
ANTENNA CABLE Bundle the excess.
74. Check that all wire harness and cables are routed properly and that all connectors are plugged in. 75. Reinstall all removed parts. Take care not to pinch the airbag with the clip during reinstallation of the A-pillar trim. Do not push excessively on the A-pillar trim. 76. Reconnect the negative cable to the battery. 77. Check the operation of the headlights and wipers. 78. Enter the anti-theft code for the audio unit and the navigation system if equipped and reset the radio station presets. 79. Reset the clock on vehicles without navigation.
FUSE BOX
80. Proceed to the REMOTE ENGINE STARTER REGISTRATION (Page 19) and FUNCTION CHECK (Page 22).
WIRE TIE DRIVER’S KICK PANEL
ENGINE STARTER HARNESS
VEHICLE HARNESS
031001BY
72. Open the hood. Using isopropyl alcohol on a shop towel, thoroughly clean the hood where the caution label will attach. ADHESIVE BACKING Remove.
HOOD Clean with isopropyl alcohol.
CAUTION LABEL 021515AY
73. Remove the adhesive backing from the caution label, and attach the caution label to the hood in the area shown. 18 of 22
AII 43923-46569 (1106)
© 2011 American Honda Motor Co., Inc. – All Rights Reserved.
REMOTE ENGINE STARTER REGISTRATION 1.
5.
Select Honda Systems, then click the check button.
Acquire the PCM Code from the Interactive Network.
CAR ICON
Select “Honda Systems.”
CHECK BUTTON 752503AS
792901AH
2.
Connect the HDS tester to the OBD II data link connector, then turn the ignition switch to the on (II) position.
3.
Start the HDS, and click the car icon.
4.
Input the VIN and other required information into the HDS, then click the check button.
6.
Select R/C ENG STARTER and click the check button.
Select “R/C ENG STARTER.”
CHECK BUTTON 752504AS
Input the VIN and other required information.
CHECK BUTTON 752502AS
© 2011 American Honda Motor Co., Inc. – All Rights Reserved.
AII 43923-46569 (1106)
19 of 22
7.
A REMARKS message will display. Click on the check button.
9.
“REMARKS” message.
The following message will display: Obtain PCM code (IMMOBILIZER PCM CODE) from iN. This vehicle’s VIN will be required to obtain the password (USA). Click on the check button. “Obtain PCM-code” message.
CHECK BUTTON 752505AS
CHECK BUTTON 752507AS
8.
Select REGISTER REMOTE CONTROL ENGINE STARTER UNIT, then click the check button. 10. Input the PCM Code, then click the check button. NOTE: To ensure security, the PCM code (password) is changed everyday, so it is impossible to register the remote control engine starter if the dates of the PCM code acquisition and registration are different. The date of the HDS tester should also be the same. Input the PCM Code.
Select “REGISTER REMOTE CONTROL ENGINE STARTER UNIT.”
CHECK BUTTON 752506AS
CHECK BUTTON 752509AS
20 of 22
AII 43923-46569 (1106)
© 2011 American Honda Motor Co., Inc. – All Rights Reserved.
11. The following message will display: The registration of the Remote Control Engine Starter Unit has been completed. Click on the check button. “The registration of the Remote Control Engine Starter Unit has been completed”.
CHECK BUTTON 752510AS
12. The following message will display: Check that the engine can be started by the Transmitter. Click on the check button. “Check that the engine can be started by the Transmitter”.
CHECK BUTTON 752511AS
13. Perform the function test on page 22, then disconnect the HDS.
© 2011 American Honda Motor Co., Inc. – All Rights Reserved.
AII 43923-46569 (1106)
21 of 22
FUNCTION CHECK Operating Conditions • The hood is closed • The shift lever is in park • The key is out of the ignition and the key is outside the vehicle • All doors and tailgate closed and locked Inspection 1.
Within 1 second, press the command button, and then the start button on the transmitter. The engine should start if all operating conditions are met.
Does the engine start? Yes - Operation is normal. No: • Make sure all “Operating Conditions” are met. • Check the engine starter harness connections. • Connect the HDS and check for an indicated failure. (Refer to the appropriate service manual for details.) 2.
Press the command button on the transmitter, and within 1 second, press the stop button. The engine should stop.
DISPLAY
Does the engine stop? COMMAND BUTTON
Yes - Operation is normal. No - Check the engine starter harness connections. 3.
STOP BUTTON
After the engine has stopped, start the engine again, and check that the engine stops after each of the following conditions:
START BUTTON
NOTE: • After each test the ignition key must be cycled, or the driver’s door must be opened and closed. •
Move the shift lever out of the P position.
•
Unlock or open the doors or the tailgate.
•
Open the hood.
•
Insert the key in the ignition.
•
Press on the brake pedal.
TRANSMITTER 732904AY
Does the engine stop after each of these tests? Yes - Operation is normal. No - Check the engine starter harness connections. 4.
Check that the power window or the moonroof does not function and the shift lever does not move to any position when the engine is started with the transmitter.
5.
Start the engine again, press the command button on the transmitter two times and check the vehicle condition on the display.
6.
Check the operation of the transmitter when the vehicle is 100 m to 150 m (325 to 490 ft.) away and in direct sight.
22 of 22
AII 43923-46569 (1106)
© 2011 American Honda Motor Co., Inc. – All Rights Reserved.
