7
6
5
4
3
DWG NO
REV
14.
MARKING, AFTER PAINTING, NOTE 13:
2.
FOR REFERENCE DOCUMENTS REFER TO: 12-P54588M ACCEPTANCE TEST PROCEDURE 12-P54589M ACCEPTANCE TEST DATA RECORD 70-P54509M INTERFACE CONTROL DRAWING 69-P54502M INTERCONNECT DIAGRAM 12-P54590M QUAL. TEST PROCEDURE 12-P54591M QUAL. TEST DATA RECORD 12-P54592M ENVIRONMENTAL TEST PROCEDURE 12-P54593M STACK TEST PROCEDURE 12-P54594M STACK TEST DATA RECORD 12-P54374M GPSIII TORQUE REQUIREMENTS
14.1
SILKSCREEN CONNECTOR REFERENCE DESIGNATION AND ESD SYMBOL IN .125 MINIMUM HIGH CHARACTERS USING WHITE INK, FIND NUMBER 42.
D 3
14.2
STEP STEP STEP STEP
1: 2: 3: 4:
TORQUE TORQUE TORQUE TORQUE
TO TO TO TO
.
8 TO 11 INCH-LBS. 18 TO 22 INCH-LBS. 28 TO 32 INCH-LBS. 38 TO 42 INCH-LBS.
5
C 7.
SOLDER ALL ELECTRICAL CONNECTIONS PER J-STD-001D, USING FIND NUMBER 58.
8
APPLY FILLET OF ADHESIVE, FIND NUMBER 69, TO CONNECTOR COVER AND SHIELD PRIOR TO PAINTING. PROCESS PER MODULE ASSEMBLY SPECIFICATION, 12-P54298M.
9
INSTALL CABLES, W10, W11, W12 AND W13, PRIOR TO PAINTING. STAKE CONNECTORS AND CABLES APPROXIMATELY WHERE SHOWN USING ADHESIVE, FIND NUMBER 69. PROCESS PER MODULE ASSEMBLY SPECIFICATION, 12-P43468D, SECTION 5.1.1.
10
TORQUE SMA CONNECTOR (.250-36UNS), TO 7.0 TO 9.0 INCH-LBS. STAKE PRIOR TO PAINTING, USING ADHESIVE, FIND NUMBER 69, PROCESS PER MODULE ASSEMBLY SPECIFICATION, 12-P54298M SECTION 3.7.
11
TORQUE TNC CONNECTORS (.4376-28UNEF), TO 12.0 TO 15.0 INCH-LBS. STAKE PRIOR TO PAINTING USING ADHESIVE, FIND NUMBER 69, PROCESS PER MODULE ASSEMBLY SPECIFICATION, 12-P54298M, SECTION 3.7.
12.
FINISH:
13.1
DO NOT PAINT SW1.
michael.henggeler 2013-03-06 6:48:51
13.2
MFR SER NO.
A
DO NOT PAINT JACK POSTS AND CONNECTOR BODY OF J2, J3, J4, J7, J8 AND J10.
13.4
DO NOT PAINT VENT HOLES.
13.5
DO NOT PAINT THE ENTIRE BOTTOM SURFACE.
13.6
DO NOT PAINT FEATURES INDICATED.
13.7
DO NOT PAINT THE ISOLATOR FOAM, SOME OR ALL PLATING MAY BE EXPOSED ALONG SIDE AND IN CLEARNCE HOLES.
13.8
APPLY ONE COAT OF PRIMER, FIND NUMBER 38, CURE PER MANUFACTURERS INSTRUCTIONS.
13.9
APPLY ONE COAT OF PAINT, FIND NUMBER 43, CURE PER MANUFACTURERS INSTRUCTIONS.
SIZE HOLE LIST
ASME Y14.1-1995 DRAWING FORMAT - 3/06
8
QTY
-ENGR APVD7
ECR00006723
11/15/12
ECR00006845
12/13/12
ECR00007102
UNDERSTILLER UNDERSTILLER UNDERSTILLER
D
15
INSTALL R901 AND R902 APPROXIMATELY WHERE SHOWN. STAKE USING ADHESIVE, FIND NUMBER 69. PROCESS PER MODULE ASSEMBLY SPECIFICATION, 12-P54298M, SECTION 3.1.
16
AFTER FINISH (PAINT), NOTE 13, AND MARKING, NOTE 14, INSTALL LEAD TAPE ON INDICATED FEATURES: SCREWS
13.7
STEP 1: 3 LAYERS OF LEAD TAPE, FIND NUMBER 314, SHOWN AS HATCHED MINIMUM COVERAGE AREA, SHALL COVER FROM SCREW TOP TO BASE MATERIAL. TAPE SHALL EXTEND OUT .25 INCHES MINIMUM FROM THE SCREW CENTER. TAPE MAY WRAP ON TO ADJACENT SURFACES.
4 SIDES, 4 HOLES
STEP 2: 2 LAYERS OF BLACK POLYIMIDE TAPE, FIND NUMBER 315, SHOWN AS MINIMUM COVERAGE AREA OUTLINE, SHALL COVER ALL LEAD TAPE SHALL EXTEND OUT .25 INCHES MINIMUM BEYOND LEAD. TAPE MAY WRAP ON TO ADJACENT SURFACES.
C
STEP 3: STAKE BLACK POLYIMIDE TAPE USING ADHESIVE, FIND NUMBER 313, AT ALL CORNERS AND AT EVERY LINEAR INCH. 17
DO NOT STAKE INDICATED HARDWARE.
WIRING TABLE
5
FROM
TO
J61-1
RFC (A7)-E8 (FWD PWR)
J61-2
RFC (A7)-E9 (REV PWR)
J61-3
RFC (A7)-E1 (GND)
P61-1
OUTPUT FILTER (A2)- VF+
P61-2
OUTPUT FILTER (A2)-VR+
P61-3
OUTPUT FILTER (A2)-GND
P52-1 (POS 2+)
A/B SWITCH (SW1) -1(RED) POS 2+
P52-2 (POS 2-)
A/B SWITCH (SW1) -2(BLK) POS 2-
P52-3 (POS 1-)
A/B SWITCH (SW1) -3(BRN) POS 1-
P52-4 (POS 1+)
A/B SWITCH (SW1) -4(WHT) POS 1+
P52-5 (POS 2 TLM/OFF)
A/B SWITCH (SW1) -5(ORN) POS 2 IND
P52-6 (POS 1 TLM/OFF)
A/B SWITCH (SW1) -6(BLU) POS 1 IND
RFC (A7)-E2 (AGC ADJ1)
RFC (A7)-E3 (AGC CNTL1)
RFC (A7)-E4 (AGC ADJ2)
RFC (A7)-E5 (AGC CNTL2)
RFC (A7)-E6 (AGC ADJ3)
RFC (A7)-E7 (AGC CNTL3)
REFERENCE ISOMETRIC VIEW SCALE 1/2
"EXPORT CONTROLLED INFORMATION WARNING This document contains technical data whose export is restricted by the Arms Export Control Act (Title 22, U.S.C., Sec 2751, et seq.) or the Export Administration Act of 1979, as amended, Title, 50, U.S.C., App. 2401 et seq. Violations of these export laws are subject to severe criminal penalties. Disseminate in accordance with provisions of DoD Directive 5230.25." COPYRIGHT 2010 - 2013 GENERAL DYNAMICS ADVANCED INFORMATION SYSTEMS PART NUMBER: 01-P54501M 001 SEE SEPARATE PARTS LIST ALL SHEETS CARRY THE SAME REVISION STATUS UNLESS OTHERWISE SPECIFIED: DIMENSIONS ARE IN INCHES TOLERANCES ON: 2 PLACE
0.01 ANGLE
3 PLACE
# 0.5
0.005
THIRD ANGLE PROJECTION
CONTR ISS
01-P54500M NEXT ASSY
DRAWING STATUS: IF THIS BOX DOES NOT CONTAIN THE WORD "RELEASED" THEN THIS DRAWING SHALL NOT BE USED FOR PROCUREMENT.
6
GPS III-ECTS
DWN CHKR QA MFG
USED ON
ENG
APPLICATION
5
4
MSB8053432
GENERAL DYNAMICS ADVANCED INFORMATION SYSTEMS,INC. 85257
ECR00004279 (-) 8/9/11 SCOTTSDALE, ARIZONA APPROVALS
MATL SYM
10/24/12
XXX
DO NOT PAINT EXPOSED THREADS AND ANY INTERNAL FEATURES OF J6, J11, J16, J17, J21, J22, J23, J25 AND J26.
13.3
UNDERSTILLER
4LDG1
PRIOR TO PAINTING: INSTALL PROTECTIVE DUST COVERS ON CONNECTORS. COVERS MAY BE TEMPORARILY REMOVED FOR MASKING.
13.
E
10/11/12
01-P54501M001
MFR CAGE CODE
FOR POINT TO POINT WIRING USE WIRE TABLE. SHEET 4, APPROXIMATE WIRE ROUTING SHOWN. STAKE WIRES AND CABLES AS REQUIRED USING ADHESIVE, FIND NUMBER 69. APPLY LACING TAPE, FIND NUMBER 45, AS REQUIRED.
D
ECR00006648
APPROVED
GENERAL DYNAMICS
MFR PN
MAINTAIN ALL REAR MODULE COVER MOUNTING SUFACES FLUSH DURING INSTALLATION OF STACK SCREWS.
6.
C
ECR00006593
DATE
IN AREA INDICATED, SILKSCREEN IN .125 MINIMUM HIGH CHARACTERS USING WHITE INK, FIND NUMBER 42, THE FOLLOWING:
MFR
STAKE MOUNTING HARDWARE USING ADHESIVE, FIND NUMBER 69. PROCESS PER MODULE ASSEMBLY SPECIFICATION, 12-P54298M, SECTION 3.8-1A, B, C. 4
B
DESCRIPTION
ECTS UNIT - GPS BLOCK III
INITIAL STACK ASSEMBLY TORQUE: TORQUE SCREWS, FIND NUMBERS 301 AND 302, SEQUENTIALLY IN FOUR (4) STEPS. COMPLETE ALL 4 STEPS FOR FIND NUMBER 301 BEFORE STARTING FIND NUMBER. SEQUENCE IS DEPICTED BY NUMBER ENCLOSED IN
B
A
PARTIAL REFERENCE DESIGNATORS ARE SHOWN. FOR COMPLETE REFERENCE DESIGNATORS PREFIX WITH _.
1
1 REVISION HISTORY
NOTES: 1.
SH
01-P54501M
M. ANDREYKA 08-12-05
W. UNDERSTILLER 8/4/11 G. HAYES
8/4/11
K. WRIGHT
8/4/11 SIZE
M. ALVARADO J. DOBOSZ
8/4/11 8/4/11
CUST MODEL: 01-P54501M
3
TITLE
2
CAGE CODE
D 4LDG1
SCALE Pro/E: 01-P54501M
ENHANCED CROSSLINK TRANSPONDER DATA UNIT ASSEMBLY 4/5
WT
DWG NO
01-P54501M
MF: 01-P54000M
1 OF 4
SHEET
REV: XB
1
DRAWING FILE: 01-P54501M E.2 MODEL FILE: 01-P54501M E.1
8
B
A
8
7
6
5
4
3
DWG NO
SH
01-P54501M
1
2
D
D
SEE SHT 3
W13
9
10
W12
9
W11
C
307
308
23
307
307
10
9
SEE SHT 3
10
(J27)
(SW1) 9X 13.2
A7
170
(J5)
THIS COVER MUST BE INSTALLED AT THE LOWER ASSEMBLY, 01-P54570M.
173 307
307
17
317 28
A4
9X NEARSIDE 9X FARSIDE 6X
1X NEARSIDE 1X FARSIDE
23 307
B
13.3
173 317
8
(J13)
(J12)
22
6X A5
2X
197
(J15)
(J14)
A6
4
C
173
17
17
24
317
6X
27
A3
B
(J24)
307 15X 14.1 A2
(J1)
307
W10
14.1
A1 6X
173 317
michael.henggeler 2013-03-06 6:48:51
25
6X
17
SEE SHT 3
11
173 317
9
17
26
"EXPORT CONTROLLED INFORMATION WARNING This document contains technical data whose export is restricted by the Arms Export Control Act (Title 22, U.S.C., Sec 2751, et seq.) or the Export Administration Act of 1979, as amended, Title, 50, U.S.C., App. 2401 et seq. Violations of these export laws are subject to severe criminal penalties. Disseminate in accordance with provisions of DoD Directive 5230.25."
A
SIZE
CAGE CODE
D 4LDG1
SCALE ASME Y14.1-1995 DRAWING FORMAT - 3/06
8
7
6
5
4
3
2
4/5
WT
DWG NO
01-P54501M SHEET
2 OF 4
1
REV
E
A
8
7
6
5
4
3 10X DO NOT PAINT HOLES
10X n .38 DO NOT PAINT 13.6
13.4
81X
DWG NO
13.6
1
3
13.4 305
4
SH
01-P54501M
302
12X
2
3
6
12
D 305
6X
14.2
173
17
317
10
13.1
310 309
8
43X
20
21
7
C
D
11
C
16
16
9 5
1
173
17
316
SW1
C-C
VIEW FROM SHEET 2
FL1 6X
3
304
4X
303 306
305
5X
DO NOT PAINT THIS SURFACE
5
13.5
1
3 10
12
B
B
3
A-A
VIEW (THIS VIEW IS ILLUSTRATED ON SHEET 4 WITHOUT COVER, FIND NUMBER 21) FROM SHEET 2
12X
305
8
301
michael.henggeler 2013-03-06 6:48:51
7
A
"EXPORT CONTROLLED INFORMATION WARNING This document contains technical data whose export is restricted by the Arms Export Control Act (Title 22, U.S.C., Sec 2751, et seq.) or the Export Administration Act of 1979, as amended, Title, 50, U.S.C., App. 2401 et seq. Violations of these export laws are subject to severe criminal penalties. Disseminate in accordance with provisions of DoD Directive 5230.25."
11
9 4
6
2
D-D
VIEW FROM SHEET 2
SIZE
8
7
6
5
4
3
CAGE CODE
D 4LDG1
SCALE ASME Y14.1-1995 DRAWING FORMAT - 3/06
A
2
4/5
WT
DWG NO
01-P54501M SHEET
3 OF 4
1
REV
E
8
7
6
"EXPORT CONTROLLED INFORMATION WARNING - This document contains technical data
5
whose export is restricted by the Arms Export Control Act (Title 22, U.S.C.,
4
3
Sec 2751, et seq.) or the Export Administration Act of 1979, as amended, Title,
W9
W15
DWG NO
50, U.S.C., App. 2401 et seq. Violations of these export laws are subject to
W2
E2
W8
E10
W4
E1
SH
01-P54501M
1
4
severe criminal penalties. Disseminate in accordance with provisions of DoD
Directive 5230.25."
W7
15
D
D (A7, RFC)
E3
E5
E4
E6
E7
E13
E11 E8
J45
5
E9
R90 2
E12
R901
J59 / P59
OPTIONAL WIRE ROUTING PATH
J46
J47
5
J50
OPTIONAL WIRE ROUTING PATH
E14 J58 / P58
(A6, SYNTH)
J57 / P57
J49
J39
J40
J41
J42
J43
J44 W5
(A5, DSP)
C
J56 / P56
J55 / P55
J38
J35
J36
J37
C
J48
J34
W6
2X 250 J52 / P52 (A4, RPC)
J54 / P54
J53 / P53
W3
173 251 (A3, PAPC)
J61
3X
W1
P60
B
J51 / P51
B
250 2X
P61
VR+
VF+
(A2, OUTPUT FILTER)
GND
155 2X
5
michael.henggeler 2013-03-06 6:48:51
OPTIONAL WIRE ROUTING PATH
A
A
(A1, PA) FL1
ASME Y14.1-1995 DRAWING FORMAT - 3/06
8
E5
E4
FL3
E3
E2
E1
FL4
FL9
FL6
J31
VIEW A-A FROM SHEET 2, 3 COVER, FIND NUMBER 159, NOT SHOWN SCALE: 1/1
7
6
5
SIZE
CAGE CODE
D 4LDG1
SCALE
4
3
2
2/1
WT
DWG NO
01-P54501M SHEET
4 OF 4
1
REV
E
