G0512 Manual - Grizzly Industrial

use face or dust mask if cutting operation is dusty. Everyday eyeglasses only have impact resistant lenses ... properly and perform its intended funct...

2 downloads 25 Views 2MB Size

Recommend Documents

CONTACT CUSTOMER SERVICE IF YOU HAVE ANY QUESTIONS ABOUT DIFFERENCES. PRE- ...... ing sanding belt when you start the machine. 3. Make sure the ...... Thank you again for your business and continued support. We hope to ...

31. 4 T2. 1 L1. 5 L3. R7. 3 L2. A1. L1. L3. L2. L2. T1. T3. T2. SP. 16/250V. Fuse. I. 5. C1. SIDE B. ROTARY SWITCH. PRINTED CIRCUIT BOARD. SIDE A. V2 L2. 5. 5. 1. 1. 1. 1 .... stood for your own safety. important: Keep this update with the owner's ma

For questions or help with this product contact Tech Support at (570) 546-9663 or [email protected] Model G0733 ..... spindle center. Tailstock: The metal component at the opposite end of the bed from the headstock containing a quill and live

stood for your own safety. IMPORTANT: Keep this .... arranged for alignment and initial assembly. Figure 5. Installing alignment screw into base panel. Rubber. Washer. Alignment. Screw. (1 of 4). Figure 3. Box 2, additional inventory. V. P. Q. R. S.

Installation. 1. disCONNeCt MaChiNe FrOM pOWer. aNd air sUppLy. 2. Using a phillips head screwdriver, remove the mounting screws from the old-style guard. (Figure 1). 3. Using a ..... tures cast iron construction for rigidity and strength, a solid ca

WARNING: NO PORTION OF THIS MANUAL MAY BE REPRODUCED IN ANY SHAPE ..... G1052 as supplied when the manual was pre- pared. However ...... ___6" - 8" Grinder. ___5" - 8" Drill Press. ___Mini Lathe. ___8" Table Saw. ___10" - 12" Thickness Planer. ___8"

1. KEEP GUARDS IN PLACE and in working order. 2. REMOVE ADJUSTING KEYS AND ... accessories may cause risk of injury. LENGTH. AMP RATING 25ft. 50ft 100ft ..... Weight. Dust Port. Sheet Metal. Standard. Standard. 1.5 H.P.-110/220V ...... SPRING. 50. P1

192. 156 155. 154. 100. 161. 177. 162. 151. 178. 157. 102. 101. 179. 170. 103. 104. 105. 160. 159. 90. 90-1. 91 ... HEX BOLT M8 - 1.25 x 25mm. 69. P1021069.

Hot. Ground. 110 VAC. 5-15 Plug. Motor. Brushes. L2. IN. L. G. A. B. L1. Fuse. F10AL250V. Fuse. F15AL250V. Gnd. 110V Motor. Gnd. JD-014 5WR02J. CESX 1101-28. ZD-SX-THL. Kedu KJD-178/120V. WX14-12. Kedu EN61058. 10A. 15A. Chip Guard. Limit Switch. Spi

KEEP CHILDREN AND VISITORS. AWAY. All children and visitors should be kept a safe distance from work area. 6. MAKE WORKSHOP CHILD PROOF with .... The electrical pack- age consists of a 3450 R.P.M., 1 H.P. capacitor start motor, locking toggle switch

to ensure proper template contact and swing before starting the ...... We recommend you keep a copy of our current catalog for complete ..... ___Card Deck. ___World Wide Web. ___Other__________________________________________________. 2. Which of the

This symbol is used to alert the user to useful information about ... manual uses a series of symbols and signal words which are intended to convey the level of .... your panel, provided you place a disconnect switch near the machine. Check the elect

exposure to these chemicals: work in a well ventilated ..... of Grizzly's growing family of fine woodworking ... Most importantly, we stand behind our machines.

THE INFORMATION IN THIS MANUAL REPRESENTS THE CONFIGURATION OF THE MACHINE. AS IT IS .... tools. If you have any service questions or parts requests, please call or write us at the location listed below. Grizzly Industrial, Inc. 1203 Lycoming Mall Ci

WARNING: NO PORTION OF THIS MANUAL MAY BE REPRODUCED IN ANY SHAPE. OR FORM WITHOUT THE WRITTEN APPROVAL OF ...... you ever remove the table in the future, be sure to make note of shim placements and ..... with respect and caution to lessen the pos- s

in a V-block. 6. DO NOT BACK WORKPIECE AWAY from the blade while the saw is running. Plan your cuts so you always cut out of the wood. If you need to ...

To position the front guard (see Figure 44), loosen the top knob bolts and slide the extension plate in or out, then loosen the front knob bolts and raise or lower the front guard as needed. Tighten the knob bolts to secure the setting. All guards MU

WARNING: NO PORTION OF THIS MANUAL MAY BE REPRODUCED IN ANY SHAPE. OR FORM ..... free, enjoyable operation and proof of Grizzly's ...... ___6" - 8" Grinder. ___5" - 8" Drill Press. ___Mini Lathe. ___8" Table Saw. ___10" - 12" Thickness Planer. ___8"

of California to cause cancer, birth defects or other reproductive harm. Some examples of these chemicals are: • Lead from lead-based paints. • Crystalline silica from bricks, cement and other masonry products. • Arsenic and chromium from chemi

The purpose of safety symbols is to attract your attention to possible hazardous conditions. This manual uses a series of symbols and signal words which are intended to convey the level of importance of the safety messages. The progres- sion of symbo

Go to Step 11. — If the blade turns counterclockwise and toward the back of the saw (standing at the left front side of the table saw), it is turning in the wrong direction. Stop the table saw, disconnect the power source, and ..... the pivot sprin

The purpose of safety symbols is to attract your attention to possible hazardous conditions. This manual uses a series of symbols and signal words which are intended to convey the level of importance of the safety messages. The progres- sion of symbo

MANY WOODWORKING TOOLS CAN. “KICKBACK” THE WORKPIECE toward the operator if not handled properly. Know what conditions can create “kickback” and know how to avoid them. Read the manual accompanying the machine thoroughly. 18. CHECK DAMAGED PA

For Machines Mfg. Since 5/11. 13" HEAVY 13® GEARHEAD LATHE. MODEL SB1049 13" X 30". MODEL SB1050 13" X 40". OWNER'S MANUAL ... For your convenience, any updates to this manual will be available to download free of charge through our website at: ....